A PE silicone core cable protection pipe high speed extruder is the production system that manufactures the smooth, low-friction HDPE duct used to protect and route communication optical cables that are buried directly in the ground. Faygo, завод Wanplas with 22 years of dedicated experience in plastic pipe and profile extrusion lines, builds these high speed co-extrusion lines for manufacturers who supply telecom operators, highway authorities, railway operators and municipal utilities. This guide explains what a silicon core duct is, how the double-layer co-extrusion system works, what a complete production line contains, which process parameters matter, how to select the right machine configuration, how to inspect the finished pipe, and how to troubleshoot the most common defects. Whether you are planning a new facility, replacing aging equipment, or expanding capacity, the information below gives you a concrete technical foundation for specifying a high speed extrusion line that produces reliable communication optical cable protection pipe.
The demand for buried optical cable duct keeps rising because fiber-to-the-home, 5G mobile backhaul, data center interconnection and smart-grid communication all depend on protected, easily upgradeable cabling routes. Conventional smooth HDPE duct can only be installed by pulling, which is slow, damages the cable jacket, and limits the length of a single installation section. The silicone core pipe solves this by placing a permanent solid silicone lubricant layer on the inner wall during extrusion, so the cable is installed by air-blowing over distances of 1000 to 2000 meters in a single operation. Producing that inner layer consistently at high line speed is exactly what a well-designed high speed extruder must deliver, and that is the focus of this article.
What Is a PE Silicone Core Cable Protection Pipe
A PE silicone core cable protection pipe, also called a silicon core duct or HDPE silicon core duct, is a high-density polyethylene conduit with a co-extruded solid silicone lubricant layer permanently bonded to its inner surface. The base tube is made from pipe-grade HDPE, while the inner layer is a thin film of silicone compound, typically 0.05 to 0.15 millimeters thick, that is extruded together with the base layer in a single pass through a multi-channel die head. The result is a single-wall duct that combines the mechanical strength and weatherability of HDPE with the permanent low friction of silicone.
The defining performance metric is the inner-wall dynamic friction coefficient. A normal HDPE pipe has a dynamic friction coefficient of about 0.35 to 0.45 against a cable jacket, which is too high for long air-blown installation. A qualified silicon core duct reduces this to 0.08 or lower. At that friction level, a compressor can blow a lightweight optical cable through the pre-laid duct at several meters per second, placing 1000 to 2000 meters of cable in one continuous operation without pulling ropes, grease, or intermediate manholes. This installation method is known as air-blown cable installation, and it is the main reason telecom operators specify silicon core duct for new networks.
The duct is produced in fixed nominal sizes expressed as outer diameter over inner diameter. The most common communication specifications are phi32/26, phi40/33, phi46/40 and phi50/41, where the first number is the outer diameter and the second is the inner diameter in millimeters. Color identification stripes, usually three or four longitudinal stripes, are co-extruded on the outer wall so that different cable routes can be distinguished inside a shared trench. The table below maps the standard specifications to wall thickness, the maximum cable outer diameter that can be installed, and the typical coil length used for transport and deployment.
Standard Технические характеристики and Coil Length Reference
| Технические характеристики (OD/ID, mm) | Nominal Толщина стенки (мм) | Max. Installed Cable OD (mm) | Standard Coil Length (m) | Typical Color Stripes |
|---|---|---|---|---|
| phi32/26 | 3.0 | 24 | 1000 / 1500 / 2000 | 3 |
| phi40/33 | 3.5 | 30 | 1000 / 1500 | 3 or 4 |
| phi46/40 | 3.0 | 36 | 1000 | 3 or 4 |
| phi50/41 | 4.5 | 38 | 1000 | 4 |
The wall thickness is determined by the difference between the outer and inner diameters divided by two, and it must stay within tolerance because both ring stiffness and the available cable clearance depend on it. The HDPE base provides the structural performance, while the thin silicone layer does none of the load bearing yet delivers almost all of the installation advantage. Because the silicone layer is so thin, holding its thickness and continuity across the full length of a high speed run is the central manufacturing challenge addressed later in this article.
Why Silicone Core Duct Outperforms Conventional Single-Layer Duct
Silicon core duct changes the economics of underground communication cabling because it moves the friction problem from the installation crew to the factory. A conventional single-layer HDPE duct relies on the base polymer surface, which is relatively rough and has a high friction coefficient. Cable placement therefore requires pulling grips, rope, and often periodic application of liquid lubricant, with short achievable lengths and a real risk of jacket damage. The silicon core duct replaces all of that with a factory-applied permanent lubricant surface.
The comparison below is a technology-to-technology comparison, not a brand comparison. It contrasts the silicon core co-extruded duct with the conventional single-layer duct that older lines still produce. This distinction matters when you evaluate whether to invest in a dedicated high speed silicon core extrusion line rather than adapting a standard pipe line.
| Аспект | PE Silicon Core Duct | Conventional Single-Layer Duct |
|---|---|---|
| Коэффициент трения внутренней стенки | 0.08 or lower (dynamic) | 0.35 to 0.45 |
| Метод установки кабеля | Air-blown, 1000 to 2000 m per blow | Pulling, short sections |
| Lubrication | Permanent solid silicone layer | Периодически смазывающийся жидкий смазка |
| Installation speed | High, continuous | Low, step by step |
| Cable jacket damage risk | Низкий уровень | Higher under pull load |
| Network upgrade convenience | Re-blow new cable anytime | Re-pull, more labor |
| Required line technology | Головка многократного экструзии с многократным покрытием | Стандартная пресс-форма с одним слоем |
For the operator, the practical benefit is lower total installed cost per meter of fiber route, faster project completion, and the ability to add capacity later simply by blowing in another cable. For the pipe manufacturer, however, the benefit comes with a manufacturing obligation: the silicone layer must be continuous, uniform and well bonded, and it must survive coiling, transport, trench laying and decades in the ground. That obligation drives every design decision in the extrusion line.
Система двойного слоя коэкструзии
Ядро трубы из кремневого материала состоит из двухслойной или, точнее, многослойной системы коэкструзии. Внешняя и основная структура HDPE производится первичным экструдером, в то время как тонкий слой силикона подается специальным небольшим коэкструдером в одну и ту же головку пресс-форми, чтобы два материала слились в зоне пресс-форми и выходили в виде одной объединенной трубы. Третий, еще меньший экструдер может добавлять цветные идентификационные полосы на внешней поверхности. Все три потока плавленого материала встречаются в трехканальной головке коэкструзии, которая является сердцем этой технологии.
The primary extruder is a single-screw machine, most often sized at 65 millimeters in diameter with a 33-to-1 length-to-diameter ratio, or scaled up to 75 millimeters diameter and 33 L/D for higher output. The screw uses a barrier design combined with a mixing head so that the HDPE melts uniformly, degasses, and builds stable pressure. Output from this machine typically ranges from 250 to 450 kilograms per hour depending on screw size and screw speed. A barrier screw with a dispersive mixing section is important because silicone masterbatch and color masterbatch are added at low percentages and must be distributed without streaks.
The silicone core co-extruder is a much smaller machine, commonly 30 millimeters diameter with 25 L/D, or 35 millimeters diameter with 25 L/D on high speed lines. It plasticizes the silicone compound at a controlled temperature and delivers a precise, low-volume melt into the inner channel of the die head. Because the silicone layer is only 0.05 to 0.15 millimeters thick, the metering accuracy of this small extruder directly controls product quality. The stripe co-extruder is even smaller, typically 20 to 25 millimeters in diameter, and it lays the colored identification stripes on the outer wall.
The three-channel die head is where the technology is won or lost. Its flow channels must keep the HDPE and silicone melts at their correct, separate temperatures until the very last moment, then join them so the silicone forms a uniform, concentric inner skin with strong interfacial bonding. Two engineering targets dominate die design. First, silicone layer uniformity: the layer thickness must stay within a tight band along the entire pipe length and around the circumference, otherwise local friction rises and air-blown performance becomes inconsistent. Second, interfacial bonding: the peel strength between the silicone layer and the HDPE base must be high enough that the layer never delaminates during coiling, bending, or installation, yet the two materials must not inter-diffuse into a mushy boundary.
Faygo supplies this co-extrusion system as part of its high speed PE silicon core линия экструзии труб, built on the same pipe extrusion platform that covers 12 to 575 millimeter diameters for water, gas, drainage and communication applications. The Faygo line uses internationally recognized brand electrical components and an intelligent control system that lets the operator set and adjust parameters in real time. The table below presents two Faygo configuration tiers for communication silicon core duct, drawn from the standard machine sizes used for this product family.
Die head temperature control deserves special attention because the HDPE and silicone melts have different thermal windows and must not be allowed to mix too early. The head is typically heated in independent zones so the operator can hold the HDPE channels near 200 to 215 Celsius while keeping the silicone channel in its narrower 180 to 200 Celsius band. Давление плавления at the die is monitored so that fluctuations, which would otherwise translate into wall thickness variation, are caught immediately. A well-built three-channel head also makes the silicone layer adjustable independently of the base wall, which is the feature that lets one line serve both thin phi32/26 duct and thicker phi50/41 duct without changing the fundamental low-friction performance.
Faygo High Speed Silicon Core Линия экструзии труб Технические характеристикиs
| Предмет | Standard Speed Конфигурация | Конфигурация высокой скорости |
|---|---|---|
| Applicable pipe OD | phi32/26, phi40/33 | phi40/33, phi46/40, phi50/41 |
| Основной винт экструдера | Одношнековая 65 мм, 33 L/D, барьер + смесительный головник | Single-screw 75 mm, 33 L/D, barrier + mixing head |
| Silicone core co-extruder | 30 mm, 25 L/D | 35 мм, 25 L/D |
| Stripe co-extruder | 20 мм | 25 мм |
| Maximum throughput | 250 to 320 kg/h | 380 to 450 kg/h |
| Maximum line speed | 30 m/min | 45 m/min |
| Установленная мощность | Approx. 145 kW | Approx. 185 kW |
| Total line length | Approx. 36 m | Приблизительно 42 м |
| Метод калибровки | Калибровка в вакууме, minus 0.02 to minus 0.05 MPa | Калибровка в вакууме, от минус 0,02 до минус 0,06 МПа |
| Тип транспортера-отводчика | Катушка намотки, 15-30 м/мин | Выгрузка катушки, 15–45 м/мин |
The downstream auxiliary equipment deserves its own specification view because it determines whether the high speed potential of the extruder is actually realized on the floor. The vacuum calibration box, spray cooling tanks, caterpillar haul-off, ink-jet printer with meter counter, dual-station chip-free cutter and automatic coiling winder must all keep pace with the die output. The table below lists the auxiliary unit parameters that Faygo configures to match the two main line tiers.
Faygo Downstream Дополнительное устройство Технические характеристикиs
| Дополнительное устройство | Standard Speed Конфигурация | Конфигурация высокой скорости |
|---|---|---|
| Коробка для калибровки вакуума | Одноступенчатый, вода 15–20 градусов Цельсия | Расширенный этап, вода 15–20 градусов Цельсия |
| Метод охлаждения | Многоступенчатый резервуар для распыления охлаждающей жидкости | Длинный многоступенчатый резервуар для распыления охлаждающей жидкости |
| Длина захвата для выгрузки | Standard caterpillar length | Удлиненная длина катушки для высокого натяжения |
| Принтер и счетчик метра | Ink-jet, length metering | Ink-jet, length metering |
| Резак | Dual-station chip-free cutter | Dual-station chip-free cutter |
| Coiling winder | Automatic, coil diameter 1000 to 2000 mm | Automatic, coil diameter 1000 to 2500 mm |
Complete Production Конфигурация линии Chain
A complete high speed silicon core линия экструзии труб is a sequence of synchronized units, each responsible for one stage of converting HDPE pellets, silicone masterbatch and color masterbatch into coiled finished duct. Understanding the chain helps you plan the factory layout, utility supply and operator workflow. The chain runs as follows.
Centralized feeding delivers the HDPE base material, silicone masterbatch and color masterbatch to the correct extruder hoppers. Gravimetric or volumetric dosing keeps the low-percentage silicone and color additions accurate, which is essential for layer uniformity. The primary and secondary extruders then plasticize their respective melts. The three-channel co-extrusion die head and its tooling, consisting of the die and the core rod, set the final pipe geometry. The gap between the die and the core rod, together with the draw-down ratio, controls wall thickness and concentricity. After the die, the molten pipe enters the vacuum calibration box.
The vacuum calibration box fixes the outer diameter by drawing the soft pipe against a cooled calibration sleeve under vacuum. The vacuum level is held at minus 0.02 to minus 0.06 megapascal, and the cooling water is kept at 15 to 20 Celsius so the surface sets quickly without thermal shock. From calibration the pipe passes through a multi-stage spray cooling water tank where the wall is fully solidified. The caterpillar haul-off then pulls the pipe at a controlled, steady speed. Because the haul-off speed sets the draw-down, it is the master variable that couples extruder output to final dimensions.
После охлаждения принтер с инжекторной формой печати наносит идентификационные данные, а счетчик метра регистрирует длину. Безотходный безмикронный резак разрезает трубу на заданную длину без образования отходов, которые могут загрязнить канал. Наконец, автоматический намотчик намотывает трубу на руло размером от 1000 до 2500 миллиметров в зависимости от размера трубы и выбранной длины транспортной катушки. Синхронизация вывода экструдера, скорости выгрузки и синхронизации резака обеспечивается системой управления линией, чтобы толщина стенки, длина и вес рулона оставались постоянными на протяжении всего производственного цикла.
С точки зрения планировки стандартная конфигурация занимает около 36 метров длины пола, а конфигурация с высокой скоростью — около 42 метров, плюс пространство для хранения материалов, обработки рулонов и подготовки готовой продукции. Служба консультирования завода Faygos может обеспечить проектирование водопровода и электроснабжения, трехмерную планировку цеха, конфигурацию рабочих и обучение в рамках проекта «под ключ», что особенно полезно для нового предприятия, построенного с нуля.
Process Parameters and Settings
Stable, repeatable process parameters are what separate a high speed line that produces qualified silicon core duct from one that produces scrap. The parameters span material selection, barrel temperature profile, die head temperature, silicone temperature, vacuum, cooling water temperature, haul-off speed and draw-down ratio. The table below consolidates the working window for communication silicon core pipe.
Process Parameter Window
| Stage / Parameter | Range / Setting | Примечания |
|---|---|---|
| HDPE grade | PE80 / PE100 pipe material | MFR от 0,2 до 0,6 г/10 мин при 190 градусах Цельсия, 5 кг; плотность от 0,945 до 0,955 |
| Зона барабана 1 temperature | 170 to 185 Celsius | Feed and compression |
| Зона трубы 2 temperature | 185 to 195 Celsius | Melting |
| Температура в зоне 3 бака | 195 to 205 Celsius | Смешивание |
| Barrel zone 4 temperature | 200 to 210 Celsius | Metering |
| Die head temperature | 200 to 215 Celsius | Uniform across head |
| Silicone material temperature | 180 to 200 Celsius | Stable for thin layer |
| калибровочное вакуумное давление | от минус 0,02 до минус 0,06 МПа | Sets outer diameter |
| Температура воды в калибровочном резервуаре | 15 to 20 Celsius | Fast surface set |
| Скорость выталкивания | 15 to 40 m/min, high speed 45 | Matches throughput |
| Draw-down ratio (DDR) | 1.2 to 1.6 | Controls wall thickness |
| Main screw speed | 20 to 60 rpm | Tune with haul-off |
Several parameter relationships deserve emphasis. The barrel temperature must increase gradually from feed to metering so that the HDPE melts without degradation; an overheated rear zone degrades the material while an underheated front zone causes melt fracture and a rough surface. The silicone melt must stay in its own narrow band so the thin layer forms smoothly; too cold and it streaks, too hot and it loses definition at the interface. The calibration vacuum and the haul-off speed together control outer diameter and wall thickness, so they are the first things to check when dimensions drift.
The draw-down ratio, defined as the ratio of the cross-sectional area of the die opening to the cross-sectional area of the finished pipe, normally sits between 1.2 and 1.6 for silicon core duct. A higher draw-down thins the wall and increases line speed but raises stress and can thin the silicone layer unevenly. A lower draw-down is gentler but limits output. The correct value is found by balancing the target wall thickness in the specification table against the available extruder output and the maximum safe haul-off speed.
Как выбрать подходящую линию Faygo для вашего проекта
Selecting the right extrusion line starts from the pipe sizes you must supply and the daily output you must achieve. A manufacturer serving a regional telecom program with mostly phi32/26 and phi40/33 duct can run a standard speed line efficiently, while a supplier covering highway and railway programs with larger phi46/40 and phi50/41 duct, or one pursuing maximum throughput, should choose the high speed configuration. The recommendation table below maps common project requirements to the Faygo configuration that fits them.
Требование к рекомендациям по конфигурации
| Target Pipe OD | Daily Output Target | Coil Length Requirement | Рекомендованная конфигурация Faygo |
|---|---|---|---|
| phi32/26 | 8 to 12 km/day | 2000 m coils | Standard speed 65 mm line |
| phi40/33 | 10–15 км/сутки | 1500 m coils | Standard or high speed 65 mm line |
| phi46/40 | 12 to 18 km/day | 1000 m coils | High speed 75 mm line |
| phi50/41 | 12 to 20 km/day | 1000 m coils | High speed 75 mm line |
| Mixed sizes | Flexible | Mixed | High speed line with quick-change tooling |
Beyond diameter and output, consider utility capacity. The high speed line draws about 185 kilowatts of installed power and needs a stable cooling water supply at 15 to 20 Celsius, so the site must provide adequate electrical service and a chiller or cooling tower. Coil handling also matters: larger 2500 millimeter coils are heavier and need proper handling equipment at both the winder and the warehouse. If your program spans several diameters, invest in quick-change die and core-rod tooling so changeovers stay short and the line utilization remains high.
Faygo, as a Wanplas factory, can also draw on the broader Wanplas group capability for adjacent needs such as material handling, dosing and centralized control, supplied as part of a customized turnkey solution rather than as a separately named product. This keeps the project single-source and accountable while remaining within the Wanplas brand family.
Quality Inspection and Acceptance Tests
Silicon core duct is judged by a specific set of tests because its value depends on the inner wall as much as on the structure. The most important test is the inner-wall friction coefficient, measured on an air-blow simulation bench that reproduces the installation condition; a qualified duct shows a dynamic friction coefficient of 0.08 or lower. Жёсткость кольца confirms the duct can resist soil load, while the falling weight impact test verifies toughness at low temperature. Продольное реверсирование, measured at 110 Celsius for one hour, must not exceed 3 percent, confirming the pipe will not shrink excessively in service. The hydrostatic test confirms the wall integrity under pressure, and the silicone layer is checked for peel strength and scratch resistance so it stays bonded and intact.
Factory Inspection Items and Acceptance Criteria
| Тестовый элемент | Method / Reference | Критерий приемки |
|---|---|---|
| Коэффициент трения внутренней стенки | Бенч для симуляции надувания воздухом | Dynamic 0.08 or lower |
| Жёсткость кольца | Жёсткость кольца test | Per stiffness class |
| Удар падающим весом | Испытание на удароудар с падающим весом | No crack at low temperature |
| Продольное реверсирование | 110 Celsius, 1 hour | 3 percent or less |
| Гидростатическое давление | Гидравлическое испытание | No failure at rated pressure and time |
| Отрыв и адгезия силиконового слоя | Peel test | No delamination |
| Scratch resistance | Тест на царапины | Слой силикона остается неповрежденным |
| Inner wall roughness Ra | Profilometer | Low, smooth surface |
| Wall thickness and eccentricity | Ultrasonic or cut section | Within specification tolerance |
| Внешний диаметр и овальность | Caliper or gauge | Within specification tolerance |
| Color stripe continuity | Visual and continuity check | Непрерывный, идентифицируемый |
These tests should be sampled continuously during the production run, not only at the end, because defects such as silicone streaks or eccentricity appear intermittently when a parameter drifts. Faygo’s quality control includes непрерывная работа 72 часа testing before shipment, which exercises the line under production conditions and confirms that it can hold these criteria over an extended run rather than for a few good minutes.
Общие дефекты и устранение неполадок
Even a well-designed line produces defects when parameters drift, tooling wears, or material varies. The table below lists the defects most often seen in silicon core pipe production, their typical causes, and the corrective action. A disciplined operator uses this as a daily reference and treats any rise in air-blow resistance as a top-priority signal because it directly defeats the product’s purpose.
Справочник дефектов, причин и мер по устранению
| Дефект | Типичная причина | Корректирующие меры |
|---|---|---|
| Silicone layer discontinuous or streaked | Неравномерная подача пенообразующей смеси, неправильная температура расплава | Stabilize dosing, adjust silicone temperature to 180 to 200 Celsius |
| Inner wall bulge | Неравномерное охлаждение, poor concentricity | Проверьте калибровку вакуума, перецентрируйте пресс-форму и стержень ядра |
| Ексцентричность толщины стенки | Core rod misaligned, uneven heating | Realign die and core rod, balance barrel zones |
| Out-of-round ovality | Insufficient vacuum, haul-off speed mismatch | Raise vacuum, balance puller speed with output |
| Дрейф цветной полосы | Смещение положения экструдера полосы | Настройте положение и выход коэкструдера ленты |
| Сжатие и рекуперация катушки | Высокая остаточная напряженность, слишком быстрая охлаждение | Медленное охлаждение, использование большего диаметра катушки |
| Высокая устойчивость к ударам воздуха | Грубая внутренняя стенка, неравномерный силикон | Проверьте слой силикона, отшлифуйте посадочное место, проверьте Ra |
| Отслаивание силикона | Плохая адгезия интерфейса | Повысьте температуру интерфейса, оптимизируйте соотношение слоев |
| Погрешность поверхности или кожа акулы | Разрыв расплава, слишком низкая температура | Повысьте температуру барабана и формы, измените скорость винта |
| Черные пятна или загрязнение | Загрязнение материала или его деградация | Прочистите расплав, почистите барабан, проверьте сменный экран |
| Различия в диаметре | Unstable haul-off, pressure fluctuation | Используйте скоростной контроль с закрытым циклом, стабилизируйте давление расплава |
| Плохая адгезия полос или выцветание | Неправильный пигмент, слабое склеивание | Используйте совместимый мастичный материал, проверьте температуру. |
| Пузырьки внутри стенки | Влажность, задержанный газ | Сухой материал, использование зоны барабана с отверстиями для отвода воздуха |
| Низкая жесткость кольца | Слишком тонкая стенка, низкое качество материала | Проверьте толщину стенки, используйте трубу класса PE100 |
Большинство этих дефектов можно отнести к трем основным причинам: нестабильное дозирование низко-процентных добавок, нецентрированная форма или стержень ядра и несинхронизированная калибровка или отводная секция. Рядовой профилактический ремонт, проверяющий точность дозирования, центрировку формы и стабильность вакуума каждый смены, позволит избежать большинства брака еще до его появления.
Применяемые отрасли and Deployment Scenarios
Communication optical cable protection pipe serves a broad set of deployment scenarios, all of which benefit from the air-blown installation that silicon core duct enables. Faygo’s линия экструзии трубs are applied across water supply, drainage, gas, communication and agricultural irrigation, and the communication and power cable protection segment is a core application of its pipe product family. The concrete scenarios for silicon core duct are described below.
Long-haul trunk optical cable direct burial is the classic use. National and provincial backbone networks lay thousands of kilometers of duct each year, and the ability to blow a cable 1000 to 2000 meters in one operation sharply reduces manhole count and labor. City and municipal pipeline communication uses the same duct inside shared utility trenches, where color stripes separate telecom, power and other services. Highway and railway corridor communication runs duct along the roadbed or right-of-way so that the operator can later add capacity without excavating the pavement. Campus and park weak-current pipe networks use silicon core duct for building-to-building fiber, where frequent upgrades make air-blown installation especially valuable. Finally, 5G base station backhaul depends on protected fiber from the antenna site to the aggregation node, and silicon core duct offers the fast, low-risk routing that dense small-cell rollouts require.
For each scenario the pipe must survive decades underground, resist soil load and moisture, and protect the cable from mechanical disturbance during and after installation. The HDPE base delivers the weathering and chemical resistance, while the silicone core delivers the installation flexibility. A manufacturer serving these markets should therefore prioritize line consistency and the friction test above almost every other quality metric.
The deployment environment also shapes the specification choices a buyer should discuss with the equipment supplier. In long-haul and highway projects the duct is often laid in sandy or rocky backfill, so wall thickness and ring stiffness class must match the burial depth and traffic load, and the color stripes must stay visible after years of trench handling. In city and campus networks the duct shares trenches with power and water lines, which raises the importance of clean identification and of a smooth inner wall that supports repeated re-blowing as bandwidth demand grows. For 5G backhaul, rollout speed is often the deciding factor, and the air-blown method lets operators light a route quickly and add fibers later without new excavation. A producer who understands these differences can stock the right diameter mix, phi32/26 through phi50/41, and tune the line to switch between them with minimal downtime.
From the manufacturer’s side, serving multiple scenarios also means planning material logistics carefully. Pipe-grade PE80 and PE100 are supplied as natural or pre-colored pellets, and the silicone and stripe masterbatches are added at low percentages, so the dosing and storage system must keep each additive clean and dry. A small amount of contaminated or moist material can cause black spots, bubbles or streaks that fail the friction and appearance tests. Reasonable in-house practice includes separate silos or covered bins for each component, routine moisture checks on the base resin, and a documented changeover procedure when moving between pipe sizes or colors. These habits protect the investment in a high speed line by keeping its output saleable.
Услуги и техническая поддержка
Покупка линии экструзии — это начало длительного производственного сотрудничества, и вспомогательные услуги определяют, достигает ли оборудование обещанного уровня производительности. Компания Faygo, завод Wanplas, структурирует свою поддержку вокруг нескольких конкретных обязательств. Перед доставкой каждая линия проходит 72-часовую непрерывную эксплуатационную проверку, чтобы проблемы, связанные с пуском в эксплуатацию, были обнаружены в заводе, а не на месте клиента. Затем линия устанавливается и вводится в эксплуатацию инженерами, которые задают параметры процесса для конкретных материалов и размеров труб клиента.
The spare parts policy provides USD 500 free spare parts per year, and damaged parts within the warranty period are replaced free of charge. Technical support is available continuously through online channels, which is critical when a parameter drift appears during a night shift. Operator training covers machine operation, routine maintenance, die changeover and basic troubleshooting so the customer team becomes self-sufficient. Дистанционное управление и техническое обслуживание capability lets the factory diagnose line issues from a distance and shorten downtime.
Faygo also operates an open-factory policy and welcomes customer visits for inspection, discussion and sample trial runs. A prospective buyer can send material and target specifications, watch the line produce sample duct, and verify the friction and dimensional performance before committing. For greenfield projects, factory consulting services cover water and electricity design, three-dimensional workshop layout, worker configuration and training, and can deliver a new factory as a turnkey project built from zero. Existing plants can use the old machine replacement and capacity expansion services to upgrade without prolonged downtime.
Часто задаваемые вопросы
Что такое трубка для защиты кабеля с силиконовым ядром?
Это трубка из ПЭ, на внутренней стенке которой нанесена коэкструдированная слой из твердого силиконового смазки. Слой силикона снижает коэффициент динамического трения до примерно 0.08, поэтому оптоволоконные кабели можно устанавливать путем надувания воздухом на большие расстояния вместо того, чтобы их тянуть.
Как работает установка кабеля с помощью силиконового ядра?
Компрессор продвигает кабель через заранее уложенную трубу с помощью постоянного низкотривиального силиконового внутреннего слоя. Одним ударом можно разместить кабель на расстояние от 1000 до 2000 метров без использования веревок или периодического смазывания, что делает процесс быстрее и мягче для оболочки кабеля.
Какое сорт HDPE используется для труб с силиконовым ядром?
Используются материалы класса PE80 или PE100, с показателем текучести пластика 0,2-0,6 грамма в течение 10 минут при температуре 190 градусов Цельсия и давлении 5 килограммов, а также плотностью в диапазоне от 0,945 до 0,955.
Какую скорость линии производства может достичь высокоскоростной экструдер?
Стандартная скоростная линия работает со скоростью 15-30 метров в минуту, в то время как линия высокой скорости, приводимая в движение 75-миллиметровым одношнековым экструдером, может достигать скорости 45 метров в минуту, в зависимости от размера трубы и толщины стенки.
Сколько цветных полос необходимо, и что они означают?
В большинстве коммуникационных труб используется три или четыре продольные цветные полосы, экструдированные на наружной стенке. Они идентифицируют различные маршруты кабелей или операторов внутри общей траншеи и должны оставаться непрерывными по всей катушке.
Каков обычное отношение вытягивания для труб с силиконовым ядром?
Отношение вытягивания обычно составляет от 1,2 до 1,6. Его устанавливают путем регулировки отверстия пресс-формы и скорости вытягивания и напрямую контролируют толщину стенки, поэтому его необходимо балансировать с выходом экструдера и максимальной безопасной скоростью линии.
Как проверяется качество продукции перед отправкой?
Faygo проводит 72-часовые испытания непрерывной работы перед доставкой, проверяя трение, толщину стенок, круглость, ударную и гидростатическую прочность, а затем обеспечивает установку, пуск в эксплуатацию и обучение операторов для подтверждения соответствия линии проектным требованиям.
Какую послепродажную поддержку предоставляет компания Faygo?
Поддержка включает бесплатную гарантийную замену, 24-часовую онлайн-техническую поддержку, удаленную диагностику, заводськую подключение и полицейскую политику для посещений и тестирования образцов.
Заключение
A PE silicone core cable protection pipe high speed extruder is a specialized co-extrusion system built to manufacture the low-friction HDPE duct that makes air-blown optical cable installation practical. The technology rests on a three-channel die head that bonds a 0.05 to 0.15 millimeter silicone layer to the HDPE inner wall, a synchronized chain from centralized feeding through vacuum calibration, spray cooling, caterpillar haul-off, printing, chip-free cutting and automatic coiling, and a disciplined set of process parameters that hold the friction coefficient at 0.08 or lower. Faygo, завод Wanplas with 22 years of pipe and profile extrusion experience, three specialized factories, 26,650 square meters of production space in Zhangjiagang, 13 national patents and CE and ISO certification, supplies these lines in standard speed and high speed configurations covering phi32/26 through phi50/41 duct.
If you are planning a new silicon core duct facility, expanding an existing line, or replacing aging equipment, the right next step is to share your target pipe sizes, daily output and coil length with our engineering team. We can configure a complete line to your specification, run sample duct on the floor for your verification, and support you from factory layout through commissioning and operator training. You are welcome to visit the factory, inspect the line, and trial the equipment with your own material before making a decision.
