Supplying domestic hot water to a building that rises one hundred meters or more is a mechanical problem long before it becomes a plumbing problem. The column of water alone loads the lowest floors with static pressure that a conventional low-rise distribution system was never designed to see, while the continuous hot service temperature silently attacks every joint, every elbow and every meter of pipe wall over a design life measured in decades rather than years. In this environment the pipe is not a passive conduit; it is a structural and hygienic component that must hold pressure, resist temperature, refuse to scale, and survive for fifty years without a single interruption. A three layer composite anti scaling PPR pipe extrusion equipment exists precisely because a single homogeneous pipe wall can no longer satisfy all of those duties at once.
The engineering answer is to stop asking one material to do everything and instead assign each function to a dedicated layer. A three-layer composite PPR pipe places an anti-scaling functional layer on the bore, a reinforcement or barrier layer in the middle, and a protective layer on the outside, co-extruding all three through one die in a single pass. The equipment that makes this pipe is therefore more than a boru ekstrüzyon hattı with extra hoppers; it is a tightly synchronized co-extrusion system in which layer ratio, melt viscosity, die geometry and cooling rate must be controlled together. This guide explains the full picture for equipment buyers and project engineers: why high-rise hot water demands the composite structure, how the three layers function, which materials and standards apply, exactly how the production line is built, what the process window looks like, how anti-scaling performance is measured, how the pipe is integrated into a tall building, and which Faygo production lines deliver it.
Faygo, a Wanplas factory with twenty-two years of dedicated pipe and profile extrusion experience, operates three specialized factories and runs a 26,650 square metre pipe, profile and sheet plant in Zhangjiagang, only two hours from Shanghai airport. The factory holds thirteen national patents including eight invention patents, and every line leaves the workshop CE and ISO certified after seventy-two hours of continuous operation testing. As part of the Wanplas group, Faygo draws on a shared engineering and service backbone that has placed plastic machinery in more than one hundred exported regions. The three-layer PPR co-extrusion line described here is a direct application of that experience to the specific failure modes of high-rise domestic hot water.
1. Four Hardships Facing Ev Tipi Sıcak Su Systems in High-Rise Buildings
A high-rise domestic hot water network is defined by four stresses that ordinary low-rise plumbing never experiences together. Each stress alone is manageable; the four acting simultaneously on a single pipe wall are what make the composite structure necessary. Understanding these four hardships is the first step in specifying the right extrusion equipment, because the equipment must be capable of producing a pipe that answers all four at once.
1.1 Static pressure at the base of a tall column
In a building one hundred meters tall, the static head of the water column at the lowest riser connection is close to one megapascal before any pump pressure is added. With distribution pumps and thermal expansion, the bottom-floor service pressure in a one-hundred-meter building commonly reaches 1.0 to 1.2 megapascal. A single-layer random copolymer pipe sized for low-rise duty would need a very thick wall to carry that pressure, which only worsens the next two problems. The composite structure lets the middle layer carry stiffness and the inner layer carry the bore condition independently, so the pressure requirement does not force an oversized, thermally sluggish wall.
1.2 Long-term continuous hot water temperature
Domestic hot water is not a gentle, intermittent service. Circulation systems hold the riser at a continuous 60 to 70 degrees Celsius so that a tap delivers hot water promptly, and safety events such as a failed mixing valve can push short-term peaks to 95 degrees Celsius. Polypropylene random copolymer tolerates this band, but sustained temperature accelerates creep, softens the wall, and accelerates every chemical reaction at the bore, including scale deposition. The equipment must therefore extrude a pipe whose long-term hoop stress rating remains adequate at elevated temperature, which is why PP-RCT with its raised minimum required strength is offered as an inner-layer option.
1.3 Scaling and biofilm formation on the bore
Hard water carrying dissolved calcium and magnesium bicarbonate deposits calcium carbonate on any surface where nucleation can start. A rough bore, a polar surface, and warm stagnant pockets are ideal nucleation sites. Over years the deposit narrows the bore, raises flow resistance, and provides a habitat for biofilm. The inner anti-scaling functional layer of the composite pipe attacks this at the source: a mirror-smooth, low-surface-energy, optionally antibacterial bore that gives calcium carbonate almost nowhere to begin. This is the single most important reason the pipe is composite rather than homogeneous, and it is the property that the extrusion equipment must hold to tight tolerance across the full length.
1.4 Fifty-year design life
Building services are not replaced on a whim. A riser buried in a wall chase or a shaft is expected to perform for the life of the building, typically fifty years, with no access for inspection and no tolerance for leakage. Fifty years of pressure, temperature cycling, thermal movement and water chemistry demands a pipe whose properties do not drift. The three-layer composite answers this through material selection, expansion control and a protected outer surface, and the extrusion equipment must reproduce that layered structure meter after meter with no delamination that could become a long-term failure path.
Dört zorluk birden bir duvar üzerinde etkili olduğunda, en sağlam yanıt işlevleri katmanlara ayırmaktır. Bu ayırma, tam da üç katmanlı ko-ekstrüzyon ekipmanının sunmasını sağlar.
2. Functional Katman yapısı of the Three-Layer Composite Anti-Scaling PPR Pipe
The three-layer composite PPR pipe is engineered as three concentric functional zones, each optimized for one job and bonded to its neighbor by a compatible or tie-mediated interface. The layer ratio is deliberately imbalanced: the middle layer carries most of the wall because it carries most of the structural and barrier duty, while the inner and outer layers stay thin because they are functional skins rather than load-bearing members. The typical split is about 20 to 25 percent inner, 50 to 60 percent middle, and 20 to 25 percent outer by wall thickness.
2.1 Inner layer: the anti-scaling functional skin
The inner layer is the surface that touches the water, so its entire design goal is to make scale and biofilm unwelcome. Three mechanisms are combined. First, the bore is finished to a high smoothness with inner wall roughness Ra not more than 0.3 micrometer, compared with 0.8 to 1.5 micrometer for ordinary PPR, because fewer surface asperities means fewer nucleation sites for calcium carbonate crystals. Second, the polymer is modified for anti-fouling, either by an antibacterial additive package that suppresses microbial film or by a low-surface-energy modification that makes the water wet the wall uniformly instead of pinning droplets and deposits. Third, where temperature permits, the inner layer can be made from PP-RCT, the beta-crystal nucleated random copolymer, which raises the long-term temperature rating of the bore itself. Because this layer is thin, a premium modified compound can be used without making the whole pipe expensive.
2.2 Middle layer: reinforcement or barrier
The middle layer is the structural heart of the wall and the place where the designer chooses the dominant property the building needs. Two options dominate. The first is glass-fiber reinforced PP-R, loaded with 10 to 20 percent glass fiber, which cuts the linear expansion coefficient from about 0.15 to 0.03 to 0.05 millimeter per meter per Kelvin. For a vertical riser dozens of meters long, that reduction is decisive: it shrinks thermal movement, reduces the number and size of fixed supports and expansion compensators, and keeps the pipe from bowing in its chase. The second option is EVOH (ethylene vinyl alcohol copolymer), an oxygen barrier used when the line is part of a closed heating circuit and must prevent oxygen from diffusing through the wall and corroding metal pumps, valves and radiators. With EVOH the oxygen permeability stays below 0.1 gram per cubic meter per day, satisfying the DIN 4726 limit for oxygen-tight plastic pipes. The choice between glass fiber and EVOH is a design decision made before the line is configured, and the co-extrusion equipment supports either.
2.3 Outer layer: protection and identification
Dış katman, borunun dünyaya karşı olan kabuğudur. Bu katmanda ultraviyole stabilizatör bulunur, bu sayede boru depolama sırasında ve yerleştirmeden önce geçici olarak maruz kaldığında korunur. Aşınmaya dayanıklıdır, bu sayede kurulum sırasında çizilmemesi sağlanır ve renk veya çizgili tanımlama sayesinde montajcılar, anti-kalklaşma kompozitini sıradan PPR'den bir göz atarak ayırt edebilirler. Ayrıca, tesisat odalarında açık kalabilecek borunun bölümleri için hava koşullarına dayanıklı bir yüzey sağlar. İnce bir kabuğa sahip olduğu için, yapısal veya hijyenik katmanlara etki etmeden renkli veya çizgili olabilir, bu nedenle kompozit boru genellikle özel bir ürün olarak açıkça işaretlenir.
2.4 Layer ratio and co-extrusion temperature matching
Holding the layer ratio constant along the full line is the central quality task of the equipment. The three melts have different viscosities and thermal sensitivities, so the co-extrusion temperatures must be matched so that no layer tries to dominate the interface. The table below shows the typical wall split and the temperature window in which the layers stay balanced. Getting this wrong is the root cause of most delamination and layer-thickness faults covered later.
| Layer | Function | Typical wall share | Co-extrusion temperature window | Key control point |
|---|---|---|---|---|
| Inner (functional) | Anti-scaling, smooth bore, optional PP-RCT | 20 to 25 percent | 200 to 225 degrees Celsius | Keep Ra low and layer centered on bore |
| Middle (structure) | Glass-fiber reinforced PP-R or EVOH barrier | 50 to 60 percent | 210 to 235 degrees Celsius (GF higher) | Carry hoop stress and expansion control |
| Outer (protection) | UV, abrasion, color identification | 20 to 25 percent | 195 to 220 degrees Celsius | Uniform skin, no streak or sink |
| Tie layer (where needed) | Bond PP to EVOH or GF-PP | 1 to 3 percent overall | 205 to 225 degrees Celsius | Adequate thermal match to both sides |
The art of three-layer pipe is not in the chemistry alone but in holding the layer ratio and the interface temperature steady for thousands of running hours. The equipment is judged by its consistency, not by a single good sample.
3. Material System and Standards for Three-Layer PPR Pipe
The composite pipe is only as good as the five materials that make up its layers and tie layers, and each material carries a specification that the raw-material system and the extrusion window must respect. The table below lists the core materials, their defining properties, and the roles they play. All values are typical engineering figures for pipe-grade compounds and should be confirmed against the specific compound certificate at procurement.
| Material | Defining property | Role in the composite pipe | Notes for the extrusion line |
|---|---|---|---|
| PP-R (Type 3 random copolymer) | Erime akışı 0,25 ila 0,5 gram / 10 dakika 230 santigrat derecede ve 2,16 kilogramdır. | Base polymer for inner and outer layers | Stable barrel window 190 to 230 degrees Celsius |
| PP-RCT (beta-crystal nucleated) | Minimum required strength raised to 11.2 megapascal | High-temperature inner layer option | Needs controlled cooling to develop beta crystals |
| PP-R GF (glass-fiber reinforced) | 10 to 20 percent glass fiber, lower expansion coefficient | Middle reinforcement layer | Abrasive; wear-resistant barrel and screw needed |
| EVOH (ethylene vinyl alcohol copolymer) | Ethylene content 32 to 44 mole percent, strong oxygen barrier | Middle barrier layer for heating circuits | Hygroscopic; requires dried feed and tie layer |
| Tie layer (PP-g-MAH) | Maleic anhydride grafted polypropylene | Bonds PP to EVOH or glass-fiber PP | Thin layer, tight temperature match |
3.1 Standards that govern the pipe
The finished pipe is judged against a stack of product and hygiene standards that the production line must be capable of satisfying. These are referenced as plain text only: ISO 15874 defines the PP piping system for hot and cold water installations; EN ISO 9080 governs the long-term hydrostatic strength extrapolation that sets the service life basis; DIN 8077 and DIN 8078 specify dimensions and the general quality requirements for PP pipes; GB/T 18742 is the Chinese national standard family for PP-R piping; ASTM F2389 covers PP pressure pipe for plumbing; NSF/ANSI 61 and NSF/ANSI 61-G certify the material for contact with drinking water; and EU 10/2011 regulates plastic food-contact materials, which for potable water means the additive package must stay within migration limits. The extrusion equipment does not itself certify the pipe, but it must be able to hold the dimensional and property consistency those standards demand.
3.2 SDR series and the pressure-temperature relationship
The standard dimension ratio, SDR, is the ratio of outside diameter to wall thickness and it sets the pressure class. For a given material the lower the SDR the thicker the wall and the higher the pressure rating. The table below shows common SDR values for PP-R composite pipe and the indicative pressure class at representative service temperatures. Pressure ratings decline with temperature because the polymer creeps faster when warm, which is exactly why the high-rise hot water duty must be read at 60 to 70 degrees Celsius, not at the 20-degree-Celsius catalog value.
| SDR, | Wall thickness ratio | Indicative PN at 20 degrees Celsius | Indicative PN at 60 degrees Celsius | Indicative PN at 70 degrees Celsius | Indicative PN at 80 degrees Celsius |
|---|---|---|---|---|---|
| SDR 6 | Thick wall | PN 20 | PN 10 to 12 | PN 8 to 10 | PN 6 to 8 |
| SDR 7.4 | Thick wall | PN 16 | PN 8 to 10 | PN 6 to 8 | PN 5 to 6 |
| SDR 9 | Medium wall | PN 12.5 | PN 6 to 8 | PN 5 to 6 | PN 4 |
| SDR 11 | Medium-thin wall | PN 10 | PN 5 to 6 | PN 4 | PN 3.2 |
Yukarıdaki basınç değerleri planlama için gösterge ilişkileridir, ISO 15874'e göre hesaplanan tasarım stresinin yerine geçmez. Kompozit yapı, orta katmanın, boru çapını daraltan duvarı kalınlaştırmadan marjı geri kazanmasını sağlar.
4. Three-Layer Co-Extrusion Line: Main Extruder and Co-Extruders
The heart of the production line is the extrusion group: one main extruder that delivers the bulk middle-layer melt, plus two co-extruders that lay down the thin inner and outer skins. Because the layers differ in volume by an order of magnitude, the machines are sized accordingly. The main extruder is a large single-screw unit; the skin extruders are small, precise single-screw units whose job is layer placement rather than bulk output.
4.1 Main extruder: single-screw with barrier screw
The main extruder uses a single screw of diameter 45 to 90 millimeter with an L/D ratio of 30 to 33 and a PP-specific barrier screw. The barrier section separates molten and solid polymer so that the melt delivered to the die is homogeneous and fully plasticized, which matters enormously for a glass-fiber or mineral-modified middle layer that must not contain unmelted agglomerates. Throughput scales with screw diameter and runs from about 120 kilogram per hour on the smallest main machine to about 800 kilogram per hour on the largest, which covers the full diameter range from 20 to 160 millimeter. The barrel is heated in independently controlled zones so the temperature profile can be tuned for PP-R, PP-RCT or the higher-temperature glass-fiber compound. For the glass-fiber middle layer the barrel and screw flight surfaces use wear-resistant treatment because glass fiber is abrasive and will otherwise erode the metering section within a season.
4.2 Two co-extruders for the functional skins
The inner anti-scaling layer and the outer protective layer are each fed by a dedicated co-extruder of 30 to 50 millimeter diameter. These machines run at low output but must be metered with high stability because a one-percent drift in skin throughput changes the layer ratio and can shift the smooth inner surface off-center. They use the same barrier-screw philosophy in miniature, with precise temperature control so the thin functional compounds, some of which contain heat-sensitive antibacterial additives, are not degraded. When the middle layer is EVOH, one of these co-extruders may instead feed the tie layer or the barrier itself, and the die distributes the layers accordingly.
4.3 Equipment specification table
Aşağıdaki tablo, temsilatif üç katmanlı hattın ekstrüzyon grubunu özetler. Boyut aralığı ve katman seçimi ile ilgili olarak, tamamen aynı Faygo ailesi boyunca, yapı sabittir.
| Machine | Screw diameter | L/D ratio | Screw type | Throughput | Main duty |
|---|---|---|---|---|---|
| Main extruder | 45 to 90 millimeter | 30 to 33 | PP barrier screw | 120 to 800 kg/h | Middle structural layer |
| Co-extruder 1 | 30 to 50 millimeter | 28 to 33 | Barrier screw | 10 to 60 kg/h | Inner anti-scaling layer |
| Co-extruder 2 | 30 to 50 millimeter | 28 to 33 | Barrier screw | 10 to 80 kg/h | Outer protection or tie layer |
| Melt pump (optional) | Matched to output | n/a | Gear pump | Stabilizes pressure | Layer uniformity |
4.4 Common debugging points for the extrusion group
When the layers drift, the cause is almost always in this group. A wandering inner-layer percentage usually traces to co-extruder screw speed instability or a feed starvation in the small hopper, which is why gravimetric or loss-in-weight feeding is preferred over volumetric for the skin lines. A lumpy middle layer points to insufficient plasticizing in the main barrel, corrected by raising the rear or middle zone a few degrees or by checking the barrier flight clearance. Glass-fiber streaking in the middle layer signals fiber agglomeration and calls for a review of the concentrate letdown and the screw shear. Stabilizing the extrusion group is the first task at every commissioning because every downstream station assumes a steady, well-melted feed.
5. Spiral Mandrel Co-Extrusion Die ve Vakum Kalibrasyonu
The die is where three independent melts become one pipe. It is the most unforgiving component on the line, because any mismatch in layer flow shows up permanently in the finished wall. The three-layer co-extrusion die used for this pipe is a spiral mandrel die, chosen because the spiral distribution gives the most uniform circumferential layer thickness of any die geometry.
5.1 Spiral mandrel die and layer uniformity
A spiral mandrel die feeds each melt through a helical channel that wraps around the mandrel, merging the streams gradually so the layer arrives at the die land as a uniform annular sheet rather than as discrete feed points. For three layers the die stacks three such distribution systems around a common mandrel, each fed from its extruder. The design target is layer thickness uniformity within plus or minus 5 percent around the circumference, because a bore that is thin on one side loses its anti-scaling margin and a middle layer that is thin on one side loses pressure rating. The melt flow channels are shaped so that the interfaces stay flat and do not wave; interface waviness is a classic failure where the thin layer thickens and thins in a repeating pattern along the pipe and eventually breaks through. Temperature of the die body is held tightly, because a few degrees of gradient across the die land changes local viscosity and distorts the layer geometry.
5.2 Vacuum calibration tank
Immediately after the die the pipe enters the vacuum calibration tank, where it is pulled onto a sizing sleeve under vacuum so that the outside diameter and roundness are set before the wall freezes. The calibration sleeve material is chosen for low friction and good heat extraction, often a treated aluminum or a sleeved steel, and its bore is the master dimension for the pipe. Vacuum is set in the range of minus 0.02 to minus 0.06 megapascal, enough to hold the soft pipe against the sleeve without collapsing it. Cooling water in the tank is kept at 12 to 18 degrees Celsius so that the outer surface sets quickly while the core stays workable long enough to avoid internal stress. Calibration is where ovality and outside diameter are locked in, so the tank length, water temperature and vacuum level are tuned together for each diameter and line speed.
5.3 Calibration and cooling parameter table
| Parametre | Typical setting | Effect if wrong |
|---|---|---|
| Calibration vacuum | minus 0.02 to minus 0.06 MPa | Too low: ovality; too high: collapse or sink |
| Calibration water temperature | 12 to 18 degrees Celsius | Too warm: poor set, large shrinkage |
| Sizing sleeve finish | Low-friction, polished bore | Rough sleeve scores the outer skin |
| First tank length | Matched to diameter and speed | Short tank: incomplete set before haul-off |
5.4 Debugging the die and calibration
The most common die fault is circumferential layer variation, corrected by balancing the spiral channel feeds and confirming that all three extruders deliver steady pressure. Interface waviness is fought by narrowing the temperature gap between adjacent layers and by slowing the line slightly so the melt relaxes before freezing. Ovality that calibration cannot remove usually means the vacuum is uneven around the sleeve or the pipe is pulled off-center; checking the centering of the die to the tank and the vacuum porting resolves most cases. Because the die and calibration together define the pipe shape, they are commissioned together and only then handed to the cooling and pull stations.
6. Downstream: Cooling, Haul-Off, Planetary Cutter and Online Inspection
Once the pipe leaves calibration it must be cooled through its full wall, pulled at a perfectly steady speed, cut without burr, stacked, and measured continuously. The downstream group looks simple but it is where line-speed stability and final dimensional quality are decided.
6.1 Spray cooling tank
After the calibration tank the pipe passes through a spray cooling tank, usually built in multiple stages so that cooling is gradual rather than shock. Gradual cooling matters for the composite pipe because the glass-fiber middle layer and the PP skins cool and shrink at different rates; too fast a quench locks in internal stress that later shows up as warpage or, worse, as a hidden delamination driver. The outlet wall temperature is held below 40 degrees Celsius before the pipe reaches the haul-off, because a warm pipe stretches under pull and loses diameter control. Multi-stage spray also lets the line run faster for a given tank length, which is how the larger-diameter configurations reach their higher throughput.
6.2 Haul-off with synchronized belts
The haul-off grips the pipe between belts and pulls it at the speed that sets the final wall thickness through the çekme oranı. For composite pipe the haul-off uses double or triple belts so the grip is distributed and the thin outer skin is not crushed, and the traction force and line speed are held in synchronization to within plus or minus 0.5 percent. A drift in pull speed is the fastest way to make the wall thickness wander, because every percent of speed change is a percent of wall thickness change at the die. Belt pressure is tuned so the pipe is held without marking, and the drive is a closed-loop servo system referenced to an encoder on the belt.
6.3 Planetary cutter and collection
The gezegen kesici travels with the pipe while cutting, so the cut is made without stopping the line and without burr. A rotating ring of blades orbits the pipe at the line speed, giving a square, clean cut face. Cut squareness matters because the pipe ends must be fusion-welded, and a skewed end makes a weak joint. After cutting, the length drops onto a tipping rack or is conveyed to a collection station where it is stacked for transfer to the test and packaging area. Because the composite pipe is heavier per meter than a single-layer wall of the same diameter, the collection system is sized for the actual finished weight, not for a light reference pipe.
6.4 Online inspection
Modern lines carry continuous inspection rather than batch sampling alone. Ultrasonic thickness gauges scan the wall and can report each layer’s thickness if the layers have distinct acoustic properties, laser gauges measure the outside diameter with micrometer accuracy, and cameras or probes sample the inner wall smoothness to confirm the anti-scaling finish. A hydrostatic test bench sits at the end of the line or in the test bay to confirm pressure rating on a representative sample. The inspection data feeds a closed-loop wall-thickness control that nudges the haul-off speed or extruder outputs to hold the target wall, so the pipe stays in tolerance across the whole production run rather than only at the start.
| Downstream station | Key parameter | Accepted tolerance |
|---|---|---|
| Spray cooling | Outlet wall temperature | below 40 degrees Celsius |
| Haul-off | Speed and traction sync | within plus or minus 0.5 percent |
| Planetary cutter | Cut face squareness | perpendicular within 1 degree |
| Online gauge | Outside diameter and wall | continuous, closed-loop corrected |
7. Process Parameter Tables for Three-Layer Co-Extrusion
İşlem penceresi, tüm üç katmanın doğru oranında ve borunun doğru boyutunda kalmasını sağlayan sıcaklık, basınç ve hızların bir setidir. Aşağıdaki tablolar, kurulumda ve üretim değişikliklerinde kullanılan çalışma referansıdır. İşaretelendirilmiş mühendislik değerleridir; gerçek sayılar, seçilen bileşimlere göre her hattın üzerinde sonlandırılır.
7.1 Barrel and die temperature profile
The main PP-R layer runs about 190 to 230 degrees Celsius across the barrel zones, with the glass-fiber middle layer run somewhat higher to keep the filled compound fluid, and the EVOH or tie layer held in its own narrow band to protect its barrier properties. The die body sits at the top of the range so the melts stay uniform as they distribute. Too cold and the layers fail to fuse; too hot and the additives degrade and the interface smears.
| Zone | PP-R inner / outer | Glass-fiber middle | EVOH / tie middle |
|---|---|---|---|
| Feed zone | 190 to 200 degrees Celsius | 195 to 210 degrees Celsius | 195 to 205 degrees Celsius |
| Compression zone | 205 to 215 degrees Celsius | 210 to 225 degrees Celsius | 205 to 215 degrees Celsius |
| Metering zone | 210 to 225 degrees Celsius | 220 to 235 degrees Celsius | 210 to 220 degrees Celsius |
| Die body | 215 to 230 degrees Celsius | 220 to 235 degrees Celsius | 215 to 225 degrees Celsius |
7.2 Melt pressure, vacuum, cooling and speed matching
Melt pressure at the die is held at 15 to 30 megapascal so the layers are pressed into intimate contact and the spiral distribution stays full. Vacuum, water temperature and line speed are matched to diameter as shown, and the wall thickness is held by a closed loop that links haul-off speed to the measured wall. The smaller diameters run fast; the larger diameters run slow because the wall mass per meter is far greater.
| Nominal diameter | Melt pressure | Calibration vacuum | Cooling water | Line speed | Throughput |
|---|---|---|---|---|---|
| 20 millimeter | 15 to 22 MPa | minus 0.02 to 0.04 MPa | 12 to 18 degrees Celsius | 12 to 22 m/min | 120 to 180 kg/h |
| 32 millimeter | 16 to 24 MPa | minus 0.02 to 0.05 MPa | 12 to 18 degrees Celsius | 8 to 16 m/min | 150 to 240 kg/h |
| 63 millimeter | 18 to 26 MPa | minus 0.03 to 0.05 MPa | 12 to 18 degrees Celsius | 4 to 9 m/min | 180 to 320 kg/h |
| 110 millimeter | 20 to 28 MPa | minus 0.04 to 0.06 MPa | 12 to 18 degrees Celsius | 2 to 5 m/min | 300 to 600 kg/h |
| 160 millimeter | 22 to 30 MPa | minus 0.04 to 0.06 MPa | 12 to 18 degrees Celsius | 1.5 to 3.5 m/min | 380 to 800 kg/h |
7.3 Wall thickness closed-loop control
The wall is not set once and forgotten. The online gauge reports outside diameter and wall, the control system compares them to the target for the selected SDR, and it trims the haul-off speed and the extruder outputs to remove drift. This closed loop is what lets a line hold tolerance across a full shift instead of only on the first spool. It also protects the expensive inner compound, because if the inner layer starts to wander thin the loop can compensate before the anti-scaling margin is lost.
8. Verifying and Quantifying Anti-Scaling Performance
The anti-scaling claim is only credible if it is measured the same way every time and reported against a reference pipe. The test method and the comparison frame below are the ones used to quantify the inner-layer performance and to express the improvement as a relative multiple rather than an absolute promise.
8.1 Scaling test method
The pipe sample is mounted in a loop through which hard water circulates at a calcium carbonate concentration of 300 to 500 milligram per liter, held at about 60 degrees Celsius, and run for 500 to 2000 hours. At the end the scale layer thickness and the mass increment per unit area are measured, the inner wall roughness is re-measured to see how much the bore has roughened, and the flow decay rate is calculated from the pressure drop at constant flow. A separate antibacterial check uses the ISO 22196 method, which counts bacterial reduction on the surface against a control. The whole battery is repeated on a reference single-layer PPR pipe of the same diameter and SDR so the comparison is fair.
8.2 Comparison against ordinary PPR
Because the inner surface of the composite pipe is smoother and lower energy, calcium carbonate nucleates far less readily, and the result is a much slower scale build-up. The table expresses the improvement as a relative multiple of the scaling rate of ordinary PPR, which is the honest way to state the benefit without implying a fixed lifetime number that depends on local water chemistry.
| Metric | Ordinary PPR (reference) | Composite anti-scaling PPR | Improvement |
|---|---|---|---|
| Inner wall roughness Ra | 0.8 to 1.5 micrometer | not more than 0.3 micrometer | smoother bore |
| Scale mass increment | Reference value | lower multiple of reference | >scaling rate reduced severalfold |
| Flow decay after test | Reference value | lower multiple of reference | flow retained longer |
| Antibacterial activity | none | reduced count per ISO 22196 | biofilm suppressed |
The precise multiple depends on water hardness, temperature and flow velocity, so the equipment and the material are validated against the customer’s actual water where that data is available. What the extrusion line guarantees is the surface quality that makes the lower scaling rate possible: a bore that stays smooth and centered for the full length of every pipe.
9. System Design Support for High-Rise Uygulamalar
Borunun yapılması işin sadece yarısıdır; boru, özelliklerinin doğru şekilde kullanılabilmesi için kurulmalıdır. Kompozit PPR boru, tek katlı duvarlara kıyasla çeşitli tasarım kurallarını değiştirir ve ekipman tedarikçisi, bitmiş bina performansını sağlamak için bu konularda tavsiyede bulunabilir.
9.1 Zoned supply and pressure reduction
Yüksek bir bina tabanının 1,0 ila 1,2 megapascal gördüğü için basınç bölümlere ayrılır, her bölümü kendi riser'ine ve basıncı azaltan valflerle korunur. Boru kalitesi ve SDR, bölgeye göre seçilir: Düşük bölgeler, daha kalın SDR veya PP-RCT iç katmanlar kullanır, yüksek bölgeler daha ince duvarlar kullanabilir. Ko-ekstrüzyon hatlarının SDR'yi sıkıca tutabilmesinin, bu bölümlenmiş tasarımın güvenli kılmasını sağlayan nedeni budur, çünkü bir duvarın ince olması, bölge hesaplamasını bozabilir.
9.2 Hot water circulation return
Soğuk suyu her uzak tüpte çekmekten kaçınmak için yüksek binalar, bir döngü çizgisi ile bir geri dönüş borusu kullanır. Su her zaman hareket halinde ve her zaman sıcak olduğunda, hareketli su, duran sudan daha yavaş çürür. Geri dönüş çizgisi, borunun en yüksek sıcaklıktaki zamanını da uzatır ve etkin ömrü artırır. Boru birleşimleri, döngü dengesini sağlamak için planlanmalıdır ve kompozit borunun kalın duvarı, birleşim ısınmasını tahmin edilebilir kılar.
9.3 Thermal expansion compensation
Cam-çelik orta katmanın 0,03 ila 0,05 milimetrelik bir Kelvin başına metrelik genişleme yapması durumunda, uzun bir dikey riser hala sıcaklıkla hareket eder ve bu hareket, genişleme bağlantıları tarafından emilmesi ve planlanan aralıklarla sabit destekler tarafından sabitlenmesi gerekir. Tablo, cam-çelik kompozit riser için önerilen sabit destek aralığını verir; sıradan PPR değer çok daha kısa olacak ve çok daha fazla destek gerekecektir. Doğru aralık, borunun takımdaki bükülmesini önler ve bağlantıları bükme sırasında yüklenmesini engeller.
| Diameter | Fixed support spacing (GF composite) | Compensation method |
|---|---|---|
| 20 to 25 millimeter | about 2.5 to 3.0 meter | Expansion joint at riser base |
| 32 to 40 millimeter | about 3.0 to 3.5 meter | Joint plus guide supports |
| 50 to 63 millimeter | about 3.5 to 4.0 meter | Joint plus guide supports |
| 75 to 110 millimeter | about 4.0 to 5.0 meter | Larger joint, fewer anchors |
9.4 Insulation and fusion joint parameters
The riser is insulated to hold the service temperature and to protect any exposed portions from ultraviolet. Joints are made by hot-melt fusion, with a melt temperature of 260 plus or minus 10 degrees Celsius and heating and cooling times scaled to diameter. The table below gives the indicative heating and cooling times; these are planning values and the jointing tool’s own schedule should be followed on site. Consistent wall from the extrusion line makes these times reliable, because the heater encounters the same wall thickness at every joint.
| Diameter | Heating time | Cooling time | Melt temperature |
|---|---|---|---|
| 20 millimeter | about 5 seconds | about 2 minutes | 260 plus or minus 10 degrees Celsius |
| 32 millimeter | about 8 seconds | about 4 minutes | 260 plus or minus 10 degrees Celsius |
| 63 millimeter | about 18 seconds | about 7 minutes | 260 plus or minus 10 degrees Celsius |
| 110 millimeter | about 35 seconds | about 12 minutes | 260 plus or minus 10 degrees Celsius |
10. Faygo Three-Layer PPR Co-Extrusion Üretim Hattıs
Faygo offers the three-layer composite PPR capability as configurations of its PP-R/PE-RT boru ekstrüzyon hattı, the same product family that covers PP-R and PE-RT pipes from 16 to 160 millimeter. Two configurations cover the diameter bands most relevant to high-rise domestic hot water, and both are built on the extrusion group, spiral mandrel co-extrusion die, vacuum calibration, spray cooling, synchronized haul-off, gezegen kesici and online inspection described above. The specifications below are representative; final values are confirmed against the chosen layer structure and compound.
10.1 Configuration A: small-to-medium diameter 20 to 63 millimeter
Bu konfigürasyon, apartmanlarda ve bir bina'nın üst katlarında en yaygın olan kol ve riser çaplarına hedefler. Orta boy bir ana extruder ile iki dış katman co-extruder ve üç katmanlı spiral mandrel die'yi bir araya getirir. Hattı, küçük bir alana sahip olmasına rağmen, apartman sıcak su boru hatlarının tüm aralığını kapsar. Anti-kalklaşma katmanı, özel bir hopper'den üretildiğinden, yapısal orta katman tarafından kirletilmez.
| Specification | Configuration A (20 to 63 millimeter) |
|---|---|
| Pipe diameter range | 20 to 63 millimeter |
| Main extruder | Single-screw 60 millimeter, L/D 33, PP barrier screw |
| Co-extruder 1 (inner) | Single-screw 30 millimeter, L/D 30 |
| Co-extruder 2 (outer or tie) | Single-screw 45 millimeter, L/D 30 |
| Throughput | 120 to 260 kilogram per hour |
| Line speed | 4 to 22 meter per minute (by diameter) |
| Installed power | about 145 kilowatt |
| Line length | about 28 meter |
| Co-extrusion layers | 3 (inner functional, middle GF or EVOH, outer) |
| Calibration method | Vacuum calibration sleeve, water 12 to 18 degrees Celsius |
10.2 Configuration B: large diameter 75 to 160 millimeter
Bu yapı, duvar kütlesi ve akış hızı en yüksek olan ana riserler ve tesis odası başlıkları için kullanılır. Ailenin en büyük ana ekstrüderi ve tam üç katmanlı die kullanılır ve bir projeye, kompozit boruda cam-çubuk genişleme kontrolü ve anti-kalkınma çapı bir üründe aynı özellikleri sunmak istendiğinde bu hatt kullanılır. Yüksek kurulum gücü ve uzun hattın, ağır büyük çaplı borunun daha fazla soğutma ve çekme yükü gerektirmesiyle ilgilidir.
| Specification | Configuration B (75 to 160 millimeter) |
|---|---|
| Pipe diameter range | 75 to 160 millimeter |
| Main extruder | Single-screw 90 millimeter, L/D 33, PP barrier screw |
| Co-extruder 1 (inner) | Single-screw 40 millimeter, L/D 30 |
| Co-extruder 2 (outer or tie) | Single-screw 50 millimeter, L/D 30 |
| Throughput | 320 to 800 kilogram per hour |
| Line speed | 1.5 to 10 meter per minute (by diameter) |
| Installed power | about 280 kilowatt |
| Line length | about 36 meter |
| Co-extrusion layers | 3 (inner functional, middle GF or EVOH, outer) |
| Calibration method | Vacuum calibration sleeve, water 12 to 18 degrees Celsius |
Both configurations share the Faygo intelligent control system, which lets operators set parameters freely and adjust in real time, and both use internationally recognized brand electrical components for reliability. They leave the plant after the standard seventy-two-hour continuous operation test, which is where the layer consistency and the closed-loop wall control are proven before shipment.
11. Requirement-to-Model Selection Guide
Doğru yapı, projelerin çap aralığına, gereken katman yapısına ve hedeflenen çıkışa doğrudan bağlıdır. Aşağıdaki tablo, yaygın yüksek binalarda kullanılan ısıtılmış su gereksinimlerini, onları karşılayan Faygo PP-R/PE-RT boru ekstrüzyon hattı yapısına haritalar. Eğer görev, içme suyu yerine kapalı bir ısıtma devresi ise, EVOH baraj orta katmanı, cam elyaf yerine seçilir.
| Çap aralığı | Layer structure | Target output | Recommended Faygo configuration |
|---|---|---|---|
| 20 to 32 millimeter | 2-layer anti-scaling (inner functional plus outer) | 120 to 180 kg/h | PP-R/PE-RT line, Configuration A, 2-layer mode |
| 20 to 63 millimeter | 3-layer with glass-fiber middle | 180 to 260 kg/h | PP-R/PE-RT line, Configuration A, 3-layer mode |
| 20 to 63 millimeter | 3-layer with EVOH barrier middle | 180 to 260 kg/h | PP-R/PE-RT line, Configuration A, EVOH mode |
| 75 to 110 millimeter | 3-layer composite, GF or EVOH | 320 to 600 kg/h | PP-R/PE-RT line, Configuration B |
| 110 to 160 millimeter | 3-layer composite, GF middle | 500 to 800 kg/h | PP-R/PE-RT line, Configuration B, high-output |
| 20 to 110 millimeter | 3-layer with PP-RCT inner, high temp | 180 to 600 kg/h | PP-R/PE-RT line, Configuration A or B with PP-RCT option |
For projects that also need other pipe families, the Wanplas group can supply adjacent extrusion lines so a single supplier covers the whole building services package, but on the faygo-china.com scope the recommendation stays within the Faygo pipe and profile extrusion product range.
12. Common Defects and Countermeasure Matrix
Even a well-designed line develops faults, and the composite structure has a few failure modes that single-layer pipe does not. The matrix below is the field reference used during commissioning and routine production. Each fault lists the likely cause and the corrective action, ordered so the operator can move from symptom to fix without guesswork.
| Hata | Likely cause | Countermeasure |
|---|---|---|
| Layer thickness uneven | Co-extruder speed drift, unbalanced spiral feed | Stabilize skin extruder with gravimetric feed; rebalance die channels |
| Inner layer delamination | Tie layer insufficient or temperature mismatch | Increase tie layer; narrow temperature gap between layers |
| Inner wall scratches | Calibration sleeve damage, foreign particles | Polish or replace sleeve; filter melt and clean feed |
| Outside diameter fluctuation | Haul-off speed drift, vacuum unstable | Recalibrate servo sync; check vacuum porting |
| Ovality over limit | Off-center die to tank, uneven vacuum | Center die; balance vacuum around sleeve |
| Inner shark skin | Inner melt too cold or too fast at die land | Raise inner layer die temperature slightly; reduce speed |
| Kabarcıklar ve su izleri | Moisture in feed, especially EVOH | Dry EVOH and hygroscopic compounds; check hopper |
| Cut burr | Dull cutter blade, wrong tracking speed | Sharpen or replace blade; match cutter to line speed |
| Hydrostatic test failure | Wall below target, weak fusion, voids | Enforce closed-loop wall control; review joint quality |
Most of these faults trace back to the same two themes: unstable extruder metering and poor temperature matching at the interface. The Faygo line’s gravimetric feeding on the skin extruders and its tight die temperature control are the design features that prevent the majority of them before they start.
13. Service and Support From Faygo
A production line is a long-term asset, and the value of the supplier is measured over the years after commissioning as much as at the moment of purchase. Faygo, as a Wanplas factory, delivers the group’s shared service承诺 through a defined support program that begins before shipment and continues through the full operating life of the line.
13.1 Testing and commissioning
Her bir hat, 72 saat süreyle fabrikada sürekli çalıştırılır ve teslim edilmeden önce onaylanır, böylece katman uyumluluğu, duvar kontrolü ve hat hızı yük altında değil de kağıt üzerinde kanıtlanmıştır. Teslimattan sonra, Faygo mühendisleri kurulum ve devreye alma konusunda yardımcı olur, hatı ithal edilen verim değerine getirir ve müşterinin bitmiş boru görmesini sağlar. Deneme üretim ve numune üretimi de, proje spesifikasyonuna göre anti-kalkışma delik bitişi ve hidrostatik numuneyi doğrulamak için gerçekleştirilir.
13.2 Spare parts, training and remote operation
The Wanplas group policy provides USD 500 free spare parts per year for the line, with warranty replacement for damaged parts inside the warranty period. Operators receive hands-on training in setup, changeover and routine maintenance, and the intelligent control system supports remote monitoring so Faygo engineers can read process data and help resolve faults without delay. Because the control platform stores recipes, a diameter or layer change can be repeated reliably once it has been tuned.
13.3 Open factory and project services
Faygo welcomes customer visits to its Zhangjiagang plant, where the 26,650 square metre facility, the three specialized factories and the running lines can be inspected directly. Beyond the machine itself, Faygo offers factory consulting covering water and electricity design, three-dimensional workshop layout, worker configuration and training, and new-factory or capacity-expansion projects. For customers who need a complete building-services pipe package, the Wanplas group can coordinate adjacent extrusion lines so the whole scope is sourced and supported under one engineering responsibility.
Sıkça Sorulan Sorular
Why use a three-layer composite structure instead of a single-layer PPR pipe for high-rise hot water?
Tek katmanlı PPR boru basınç ve sıcaklığa karşı dayanıklıdır, ancak aynı anda skalama, oksijen girişi, lineer genişleme ve yüzey kirlenmesini kontrol edemez. Üç katmanlı kompozit fonksiyonları ayırır: içteki anti-skalama işlevli katman deliği düzgün tutar, ortadaki cam elyaf veya EVOH katman genişleme veya oksijen geçirgenliğini kontrol eder ve dış katman UV ve mekanik hasarlara karşı dayanıklıdır. Bu ayrım, her katmanın diğerlerini bozmadan optimize edilmesini sağlar.
What is the difference between a glass-fiber middle layer and an EVOH middle layer?
Glass-fiber reinforced PP-R lowers the linear expansion coefficient from about 0.15 to 0.03 to 0.05 millimeter per meter per Kelvin, which stabilizes long vertical risers and reduces the number of fixed supports. EVOH (ethylene vinyl alcohol copolymer) is an oxygen barrier used in closed heating circuits to stop oxygen diffusing through the wall and corroding metal pumps and valves, keeping oxygen permeability below 0.1 gram per cubic meter per day per DIN 4726. Many domestic hot water lines choose the glass-fiber version; heating systems choose EVOH.
How is anti-scaling performance of the inner layer verified?
The standard approach circulates hard water with 300 to 500 milligram per liter calcium carbonate at about 60 degrees Celsius for 500 to 2000 hours, then measures scale layer thickness, mass increment, inner wall roughness and flow decay. Antibacterial function is checked by the ISO 22196 method. The result is compared against a reference single-layer PPR pipe to express scaling rate reduction as a relative multiple rather than an absolute figure.
What extruder configuration does a three-layer PPR co-extrusion line use?
The line uses one main single-screw extruder, typically diameter 45 to 90 millimeter with L/D 30 to 33 and a PP barrier screw, plus two co-extruders of 30 to 50 millimeter for the inner functional layer and the middle or outer layer. A spiral mandrel co-extrusion die combines the three melts into a pipe with layer uniformity within plus or minus 5 percent.
Which Faygo production line fits a given diameter and layer structure?
20 ila 63 milimetre üç katmanlı PPR için, küçük-orta çap konfigürasyonunda bulunan Faygo PP-R/PE-RT boru ekstrüzyon hattı, 120 ila 260 kilogram/saat kapasiteye sahiptir. 75 ila 160 milimetre üç katmanlı kompozit boru için büyük çap konfigürasyonu, 320 ila 800 kilogram/saat kapasiteye sahiptir. Her iki konfigürasyon da aynı Faygo PP-R/PE-RT boru ekstrüzyon hattı ürün ailesinin bir parçasıdır ve vakum kalibrasyonu, gezegenli kesme ve online kontrolü paylaşır.
What melt temperature and calibration conditions are typical for three-layer PPR?
PP-R temel katmanlar, duvar bölmelerinde 190 ila 230 santigrat derecede çalışırken, cam-çubuk veya EVOH katmanı, mukavemetini eşitlemek için biraz daha yüksektir. Ekstrüzyon die'sinde erime basıncı 15 ila 30 megapascal, vakum kalibrasyonu 12 ila 18 santigrat derecede soğutma suyu ile negatif 0,02 ila negatif 0.06 megapascal olarak ayarlanır ve püskürtme tankından çıkış duvar sıcaklığı 40 santigrat derecenin altına düşer.
How does Faygo support installation and after-sales for a complete line?
Every line is run for 72 hours of continuous operation testing before delivery, then engineers assist with installation and commissioning, trial production and sampling. The Wanplas group policy provides USD 500 free spare parts per year plus warranty replacement, 24/7 online technical support, operator training and an open factory welcome for customer visits and audits.
Sonuç
The domestic hot water system of a one-hundred-meter building asks more of its pipe than any low-rise network: it demands pressure resistance at the base, temperature endurance at the top, a bore that refuses to scale for fifty years, and a wall that does not buckle as it heats and cools. A three-layer composite anti-scaling PPR pipe answers all four by assigning each duty to its own layer, and the extrusion equipment that makes it is a synchronized co-extrusion system built around a stable extrusion group, a spiral mandrel die, vacuum calibration, steady haul-off and continuous inspection.
Faygo, a Wanplas factory with twenty-two years of pipe and profile extrusion experience, builds this capability into its PP-R/PE-RT boru ekstrüzyon hattı in configurations covering 20 to 160 millimeter, with the layer structure, throughput and control needed for genuine high-rise duty. Every line is proven over seventy-two hours before shipment, supported by the Wanplas group’s USD 500 free spare parts per year policy, remote operation assistance and open-factory access.
If you are specifying equipment for a high-rise domestic hot water project, send us your diameter range, target output, layer structure and local water chemistry. Our engineering team will return a tailored line configuration, arrange a trial production and sampling at our Zhangjiagang plant, and walk you through commissioning and operator training so the pipe you make meets the building’s fifty-year expectation from the first meter to the last.
